ISO 9001:2015IBR ApprovedEstablished 1971Full Material Traceability
GroupRequest a quote
Nickel alloysNickel alloy forgings, fittings & pipeTG-MG-088 · Rev. 1 · October 2026

Alloy 800 / 800H / 800HT — Chemical Composition & Mechanical Properties

Alloy 800 / 800H / 800HT is a nickel alloys grade for nickel alloy forgings, fittings & pipe (UNS N08800 / N08810 / N08811, EN / W.Nr 1.4876 / 1.4958 / 1.4959). It is also known as Incoloy 800 / 800H / 800HT (trade names). This sheet summarises its chemical composition limits, minimum mechanical properties, heat treatment and typical service. Teshi Group manufactures flanges and fittings in this grade.

Download PDF Request a quoteA4 · Teshi Group document TG-MG-088 · © Teshi Group · controlled document

Alloy 800 / 800H / 800HT at a glance

SpecificationAlloy 800 / 800H / 800HT
Material familyNickel alloys
Product formNickel alloy forgings, fittings & pipe
UNS numberN08800 / N08810 / N08811
EN / W.Nr equivalent1.4876 / 1.4958 / 1.4959
Also known asIncoloy 800 / 800H / 800HT (trade names)
DocumentTG-MG-088 · Rev. 1 · October 2026

Typical service

Reformer and cracker piping, heat exchangers, high-temperature service

Heat treatment

800: annealed; 800H: solution annealed 1121 °C (2050 °F) min; 800HT: solution annealed 1149 °C (2100 °F) min; 800H/800HT grain size ASTM 5 or coarser

Chemical composition of Alloy 800 / 800H / 800HT (weight %)

Ni30.0–35.0
Cr19.0–23.0
Fe39.5 min
C0.10 max (800), 0.05–0.10 (800H), 0.06–0.10 (800HT)
Mn1.50 max
Si1.0 max
S0.015 max
Cu0.75 max
Al0.15–0.60
Ti0.15–0.60
Al+Ti0.85–1.20 (800HT)

Single values are maximums unless shown as a range or “min”.

Mechanical properties

Tensile strength, min517 MPa
Yield strength (0.2 % offset), min207 MPa
Elongation, min30 %
800H / 800HT tensile, min450 MPa
800H / 800HT yield, min170 MPa
HardnessNot specified

About nickel alloys

Nickel alloys are used where stainless steels run out of corrosion or temperature resistance. With 30–99 % nickel and additions of chromium, molybdenum, copper or tungsten, they resist strong acids, chlorides, caustics and oxidation from cryogenic temperatures to above 1000 °C.

Reference information compiled from the published standard for convenience. It does not replace the current edition of the governing standard, which takes precedence. Verify critical dimensions and properties before design, purchase or fabrication. Teshi Engineers & Sales Promoters (P) Ltd accepts no liability for errors or omissions.

International equivalents of Alloy 800 / 800H / 800HT

All equivalents
Standard systemNearest equivalent grade
USA — specificationAlloy 800 / 800H / 800HT
USA — UNSN08800 / N08810 / N08811
Europe — EN designationX10NiCrAlTi32-21 / X5NiCrAlTi31-20
Europe — W.Nr1.4876 / 1.4958 / 1.4959
Japan — JISNCF800 / NCF800H
China — GB / NBNS1101 / NS1102 (GB/T 15007)
China — old GB designation0Cr20Ni32AlTi
UK — BS (withdrawn)NA15 / NA15H

Equivalents are the nearest commonly cited grades. Chemistry, mechanical properties and testing differ between standards — compare them before substituting one for another.

Same alloy in other product forms

Product formSpecification / grade
Flanges & forged fittingsASTM B564 N08800 / N08810 / N08811
Butt-weld fittingsASTM B366 WPNIC / WPNIC10 / WPNIC11
Seamless pipeASTM B407
PlateASTM B409
BarASTM B408

FAQ

Alloy 800 / 800H / 800HT: common questions

What is the minimum yield strength of Alloy 800 / 800H / 800HT?

207 MPa, with a minimum tensile strength of 517 MPa.

What is the carbon content of Alloy 800 / 800H / 800HT?

0.10 max (800), 0.05–0.10 (800H), 0.06–0.10 (800HT) %.

What is the UNS number and EN equivalent of Alloy 800 / 800H / 800HT?

UNS N08800 / N08810 / N08811; the nearest European designation is W.Nr 1.4876 / 1.4958 / 1.4959. Equivalents are close but not identical — check the specification if substituting.

How is Alloy 800 / 800H / 800HT heat treated?

800: annealed; 800H: solution annealed 1121 °C (2050 °F) min; 800HT: solution annealed 1149 °C (2100 °F) min; 800H/800HT grain size ASTM 5 or coarser.

What is the Chinese (GB) equivalent of Alloy 800 / 800H / 800HT?

The nearest Chinese equivalent is NS1101 / NS1102 (GB/T 15007), formerly 0Cr20Ni32AlTi. Equivalents are close but not identical — compare chemistry and properties before substituting.

What is the JIS equivalent of Alloy 800 / 800H / 800HT?

The nearest Japanese (JIS) equivalent is NCF800 / NCF800H.

Does Teshi Group supply Alloy 800 / 800H / 800HT?

Teshi Group manufactures flanges and fittings in this grade. Send your size, rating and quantity to info@teshigroup.com for a quotation with EN 10204 3.1 certificates.

Ready to build to spec?

Share your drawing, bill of materials or technical requirements with the Teshi team.