ISO 9001:2015IBR ApprovedEstablished 1971Full Material Traceability
GroupRequest a quote
Nickel alloysNickel alloy forgings, fittings & pipeTG-MG-085 · Rev. 1 · October 2026

Alloy 625 (UNS N06625) — Chemical Composition & Mechanical Properties

Alloy 625 (UNS N06625) is a nickel alloys grade for nickel alloy forgings, fittings & pipe (UNS N06625, EN / W.Nr 2.4856). It is also known as Inconel 625 (trade name). This sheet summarises its chemical composition limits, minimum mechanical properties, heat treatment and typical service. Teshi Group manufactures flanges and fittings in this grade.

Download PDF Request a quoteA4 · Teshi Group document TG-MG-085 · © Teshi Group · controlled document

Alloy 625 (UNS N06625) at a glance

SpecificationAlloy 625 (UNS N06625)
Material familyNickel alloys
Product formNickel alloy forgings, fittings & pipe
UNS numberN06625
EN / W.Nr equivalent2.4856
Also known asInconel 625 (trade name)
PREN (min values)46.4
DocumentTG-MG-085 · Rev. 1 · October 2026

Typical service

Seawater, flue gas, sour gas, chloride and acid service

Heat treatment

Annealed 870 °C min (grade 1)

Chemical composition of Alloy 625 (UNS N06625) (weight %)

Ni58.0 min
Cr20.0–23.0
Mo8.0–10.0
Nb+Ta3.15–4.15
Fe5.0 max
C0.10 max
Mn0.50 max
Si0.50 max
P0.015 max
S0.015 max
Al0.40 max
Ti0.40 max
Co1.0 max

Single values are maximums unless shown as a range or “min”.

Mechanical properties

Tensile strength, min827 MPa
Yield strength (0.2 % offset), min414 MPa
Elongation, min30 %
HardnessNot specified

About nickel alloys

Nickel alloys are used where stainless steels run out of corrosion or temperature resistance. With 30–99 % nickel and additions of chromium, molybdenum, copper or tungsten, they resist strong acids, chlorides, caustics and oxidation from cryogenic temperatures to above 1000 °C.

Reference information compiled from the published standard for convenience. It does not replace the current edition of the governing standard, which takes precedence. Verify critical dimensions and properties before design, purchase or fabrication. Teshi Engineers & Sales Promoters (P) Ltd accepts no liability for errors or omissions.

International equivalents of Alloy 625 (UNS N06625)

All equivalents
Standard systemNearest equivalent grade
USA — specificationAlloy 625 (UNS N06625)
USA — UNSN06625
Europe — EN designationNiCr22Mo9Nb
Europe — W.Nr2.4856
Japan — JISNCF625
China — GB / NBNS3306 (GB/T 15007) / GH3625
China — old GB designation0Cr20Ni65Mo10Nb4
UK — BS (withdrawn)NA21

Equivalents are the nearest commonly cited grades. Chemistry, mechanical properties and testing differ between standards — compare them before substituting one for another.

Same alloy in other product forms

Product formSpecification / grade
Flanges & forged fittingsASTM B564 N06625
Butt-weld fittingsASTM B366 WPNCMC
Seamless pipeASTM B444 N06625
Welded pipeASTM B705 N06625
PlateASTM B443 N06625
BarASTM B446 N06625

FAQ

Alloy 625 (UNS N06625): common questions

What is the minimum yield strength of Alloy 625 (UNS N06625)?

414 MPa, with a minimum tensile strength of 827 MPa.

What is the carbon content of Alloy 625 (UNS N06625)?

0.10 max %.

What is the PREN of Alloy 625 (UNS N06625)?

About 46, calculated as Cr + 3.3Mo + 16N using the specification minimum values. Typical heats are a little higher.

What is the UNS number and EN equivalent of Alloy 625 (UNS N06625)?

UNS N06625; the nearest European designation is W.Nr 2.4856. Equivalents are close but not identical — check the specification if substituting.

How is Alloy 625 (UNS N06625) heat treated?

Annealed 870 °C min (grade 1).

What is the Chinese (GB) equivalent of Alloy 625 (UNS N06625)?

The nearest Chinese equivalent is NS3306 (GB/T 15007) / GH3625, formerly 0Cr20Ni65Mo10Nb4. Equivalents are close but not identical — compare chemistry and properties before substituting.

What is the JIS equivalent of Alloy 625 (UNS N06625)?

The nearest Japanese (JIS) equivalent is NCF625.

Does Teshi Group supply Alloy 625 (UNS N06625)?

Teshi Group manufactures flanges and fittings in this grade. Send your size, rating and quantity to info@teshigroup.com for a quotation with EN 10204 3.1 certificates.

Ready to build to spec?

Share your drawing, bill of materials or technical requirements with the Teshi team.