EN 1092-1 Plate Flange (Type 01) & Blind Flange (Type 05) Dimensions
This chart gives EN 1092-1 Type 01 plate flange (plate flange for welding) and Type 05 blind flange dimensions in millimetres for PN 6, PN 10, PN 16 and PN 40 — outside diameter, bore and thickness. Drilling (bolt circle, holes and bolts) is common to every EN 1092-1 flange type of the same DN and PN and is on the EN 1092-1 flange charts.
Plate flanges are Teshi Group's core product: cut, machined and drilled in our own works in India from DN 10 up to 8000 NB (8 metres), in carbon, boiler-quality, stainless, duplex and nickel-alloy plate, with EN 10204 3.1 certificates.
Key to dimensions
- D
- Outside diameter of flange
- B
- Bore (inside diameter) of plate flange
- C
- Flange thickness — plate or blind, raised face (RF) or flat face (FF)
EN 1092-1 Plate Flange (Type 01) & Blind Flange (Type 05) Dimensions — tables
EN 1092-1 PN 6 — Type 01 plate and Type 05 blind flange (mm)
| SizeNB | DFlange OD · mm | BBore · mm | CPlate, RF · mm | CBlind, RF · mm |
|---|---|---|---|---|
| 10 | 75 | 19.2 | 12 | 12 |
| 15 | 80 | 23.3 | 12 | 12 |
| 20 | 90 | 28.9 | 14 | 14 |
| 25 | 100 | 35.7 | 14 | 14 |
| 32 | 120 | 44.4 | 14 | 14 |
| 40 | 130 | 50.3 | 14 | 14 |
| 50 | 140 | 62.3 | 14 | 14 |
| 65 | 160 | 78.1 | 14 | 14 |
| 80 | 190 | 90.9 | 16 | 16 |
| 100 | 210 | 116.3 | 16 | 16 |
| 125 | 240 | 141.7 | 18 | 18 |
| 150 | 265 | 170.3 | 18 | 18 |
| 200 | 320 | 221.1 | 20 | 20 |
| 250 | 375 | 275 | 22 | 22 |
| 300 | 440 | 325.9 | 22 | 22 |
EN 1092-1 PN 10 — Type 01 plate and Type 05 blind flange (mm)
| SizeNB | DFlange OD · mm | BBore · mm | CPlate, RF · mm | CBlind, RF · mm |
|---|---|---|---|---|
| 10 | 90 | 18 | 14 | 14 |
| 15 | 95 | 22 | 14 | 14 |
| 20 | 105 | 27.5 | 14 | 14 |
| 25 | 115 | 34.5 | 16 | 16 |
| 32 | 140 | 43.5 | 18 | 18 |
| 40 | 150 | 49.5 | 18 | 18 |
| 50 | 165 | 61.5 | 20 | 20 |
| 65 | 185 | 77.5 | 20 | 20 |
| 80 | 200 | 90.5 | 20 | 20 |
| 100 | 220 | 116 | 22 | 22 |
| 125 | 250 | 141.5 | 22 | 22 |
| 150 | 285 | 170.5 | 24 | 24 |
| 200 | 340 | 221.5 | 24 | 24 |
| 250 | 395 | 276.5 | 26 | 26 |
| 300 | 445 | 327.5 | 26 | 26 |
EN 1092-1 PN 16 — Type 01 plate and Type 05 blind flange (mm)
| SizeNB | DFlange OD · mm | BBore · mm | CPlate, RF · mm | CBlind, RF · mm |
|---|---|---|---|---|
| 10 | 90 | 18 | 14 | 14 |
| 15 | 95 | 22 | 14 | 14 |
| 20 | 105 | 27.5 | 14 | 14 |
| 25 | 115 | 34.5 | 16 | 16 |
| 32 | 140 | 43.5 | 18 | 18 |
| 40 | 150 | 49.5 | 18 | 18 |
| 50 | 165 | 61.5 | 20 | 20 |
| 65 | 185 | 77.5 | 20 | 20 |
| 80 | 200 | 90.5 | 20 | 20 |
| 100 | 220 | 116 | 22 | 22 |
| 125 | 250 | 141.5 | 22 | 22 |
| 150 | 285 | 170.5 | 24 | 24 |
| 200 | 340 | 221.5 | 26 | 26 |
| 250 | 405 | 276.5 | 29 | 29 |
| 300 | 460 | 327.5 | 32 | 32 |
| 350 | 520 | 359 | 35 | 35 |
| 400 | 580 | 411 | 38 | 38 |
| 450 | 640 | 462 | 42 | 42 |
| 500 | 715 | 513.5 | 46 | 46 |
| 600 | 840 | 616.5 | 52 | 52 |
EN 1092-1 PN 40 — Type 01 plate and Type 05 blind flange (mm)
| SizeNB | DFlange OD · mm | BBore · mm | CPlate, RF · mm | CBlind, RF · mm |
|---|---|---|---|---|
| 10 | 90 | 18 | 14 | 14 |
| 15 | 95 | 22 | 14 | 14 |
| 20 | 105 | 27.5 | 16 | 16 |
| 25 | 115 | 34.5 | 16 | 16 |
| 32 | 140 | 43.5 | 18 | 18 |
| 40 | 150 | 49.5 | 18 | 18 |
| 50 | 165 | 61.5 | 20 | 20 |
| 65 | 185 | 77.5 | 22 | 22 |
| 80 | 200 | 90.5 | 24 | 24 |
| 100 | 235 | 116 | 26 | 26 |
| 125 | 270 | 141.5 | 28 | 28 |
| 150 | 300 | 170.5 | 30 | 30 |
| 200 | 375 | 221.5 | 36 | 36 |
| 250 | 450 | 276.5 | 42 | 42 |
| 300 | 515 | 327.5 | 48 | 48 |
| 350 | 580 | 359.5 | 54 | 54 |
| 400 | 660 | 411 | 60 | 60 |
| 450 | 685 | 462 | 66 | 66 |
| 500 | 755 | 513.5 | 72 | 72 |
| 600 | 890 | 616.5 | 84 | 84 |
Notes
- All dimensions are in millimetres; sizes are nominal bore (NB / DN).
- Plate flange thickness is given for raised-face (RF) and flat-face (FF) flanges; where only RF is shown, the FF thickness is the same.
- Reference values for estimation and checking. Verify against the current edition of the standard and the purchase specification before design, purchase or fabrication.
Reference information compiled from the published standard for convenience. It does not replace the current edition of the governing standard, which takes precedence. Verify critical dimensions and properties before design, purchase or fabrication. Teshi Engineers & Sales Promoters (P) Ltd accepts no liability for errors or omissions.
FAQ
EN 1092-1 Plate Flange (Type 01) & Blind Flange (Type 05) dimensions: common questions
What is an EN 1092-1 Type 01 flange?
Type 01 is the plate flange for welding — a flat ring slipped over the pipe and fillet-welded. It replaces DIN 2573 (PN 6) and DIN 2576 (PN 10).
Where is the EN 1092-1 drilling?
Bolt circle, holes and bolt sizes are on the EN 1092-1 PN 6, 10, 16 and 40 flange dimension charts; they are the same for plate, weld neck and blind flanges of the same DN and PN.
Related products, data sheets and standards
Slip-On Flange
OEM manufacturer
View online · PDFTechnical data sheetBlind Flange
OEM manufacturer
View online · PDFEN 1092-1EN 1092-1 PN16 flange dimensions
PN16 weld neck, slip-on, plate and blind flange drilling and thickness, DN10–600, in mm.
View online · PDFEN 1092-1EN 1092-1 PN10 flange dimensions
PN10 weld neck, slip-on, plate and blind flange drilling, DN10–600, in mm.
View online · PDFEN 1092-1EN 1092-1 PN6 flange dimensions
EN 1092-1 PN6 flange dimensions in mm: OD, bolt circle, holes, bolts, thickness by flange type and raised face.
View online · PDF
Ready to build to spec?
Share your drawing, bill of materials or technical requirements with the Teshi team.