ISO 9001:2015IBR ApprovedEstablished 1971Full Material Traceability
GroupRequest a quote
IBRSA234 WP11Form III-C

IBR SA234 WP11 Fittings

Teshi Group is an IBR approved OEM manufacturer of IBR SA234 WP11 fittings in India — elbows, tees, reducers, caps and stub ends to ASME B16.9, NPS ½″–48″, matched to the pipe schedule — for superheated steam to about 550 °C.

Every lot is inspected by the Inspecting Authority and supplied with the IBR certificate of manufacture and test (Form III-C), EN 10204 3.1 mill certificates and full heat-number traceability.

Request an IBR quote info@teshigroup.comIBR approved · ISO 9001:2015 · since 1971

IBR SA234 WP11 Fittings at a glance

SupplyOEM manufacturer — Teshi Group, India
MaterialASTM A234 WP11 Cl.1 · ASME SA-234 WP11 Cl.1
UNSK11597
EN equivalent13CrMo4-5
Chinese GB equivalent15CrMoG (GB/T 5310) / 14Cr1MoR (GB/T 713.2)
Productselbows, tees, reducers, caps and stub ends to ASME B16.9, NPS ½″–48″, matched to the pipe schedule
Typical IBR serviceSuperheated steam to about 550 °C
CertificateIBR Form III-C countersigned by the Inspecting Authority; EN 10204 3.1

Chemical composition and strength

GradeC%Cr%Mo%YieldMPa minTensileMPa minHeat treatment
ASTM A234 WP11 Cl.10.05–0.151.00–1.500.44–0.65205415Annealed or normalized & tempered

Full ASTM A234 WP11 Cl.1 data sheet and PDF →

Matching IBR components

ComponentGradeIBR certificate
PipeASTM A335 P11Form III-A
Butt-weld fittingsASTM A234 WP11 Cl.1Form III-C
Flanges & forged fittingsASTM A182 F11 Cl.2Form III-C

How Teshi Group makes and certifies IBR material

Step 1

Order review

Confirm IBR applicability, design pressure and temperature, material grade, size, rating and the Inspecting Authority named in the order.

Step 2

IBR-acceptable raw material

Forging bar, billets, plate or pipe bought with mill certificates acceptable under IBR (Well-known Steel Maker or Inspecting Authority-tested material), recorded by heat number.

Step 3

Manufacture

Forging, heat treatment and machining to ASME B16.5, B16.47, B16.9 or B16.11, with the heat number transferred to every piece.

Step 4

Inspection and testing

Chemical and mechanical tests, hardness, dimensional inspection and NDT as required, witnessed and verified by the Inspecting Authority.

Step 5

Stamping and certificate

Each piece is hard-stamped and the IBR certificate of manufacture and test is signed by Teshi Group and countersigned by the Inspecting Authority.

Step 6

Dispatch

Material ships with the IBR certificate, EN 10204 3.1 mill test certificates and the dimensional report, traceable piece by piece.

IBR certificates

Certificate (IBR 1950 name)What it certifiesUsed for
Form III-ACertificate of manufacture and test of steam pipesIBR pipes
Form III-BCertificate of manufacture and test of tubes, signed by the Inspecting Authority or a Well-known Tube MakerBoiler tubes
Form III-CCertificate of manufacture and test of boiler mountings and fittings — the certificate buyers ask for with IBR flanges, fittings and valvesIBR flanges and fittings
Form III-FCertificate of manufacture and test of castings, by the Inspecting Authority or a Well-known FoundryCast valve bodies
Form III-GCertificate of manufacture and test of forgings, by the Inspecting Authority or a Well-known ForgeForgings
Form IVSteel maker's certificate of manufacture and test (Well-known Steel Maker)Raw material
Form IV-ACertificate of material tested by the Inspecting Authority where the maker's certificate is not availableRaw material

The Indian Boiler Regulations, 2026 consolidate these certificates under a renumbered set of forms. Until your boiler inspectorate confirms the form required on a specific job, buyers and inspectors still refer to the 1950 names — Form III-A for pipes and Form III-C for flanges and fittings — and Teshi Group issues the certificate in the form prescribed at the time of supply.

FAQ

IBR SA234 WP11 Fittings: common questions

Do you supply SA234 WP11 fittings with IBR certificates?

Yes. Teshi Group supplies IBR SA234 WP11 fittings with the IBR certificate (Form III-C) countersigned by the Inspecting Authority, plus EN 10204 3.1 mill test certificates.

What is the minimum yield strength of SA234 WP11?

205 MPa, with a minimum tensile strength of 415 MPa.

Where is SA234 WP11 used in IBR piping?

For superheated steam to about 550 °C.

Which grades match SA234 WP11 in an IBR line?

ASTM A335 P11 pipe, ASTM A234 WP11 Cl.1 butt-weld fittings and ASTM A182 F11 Cl.2 flanges.

What is the Chinese equivalent of SA234 WP11?

The nearest Chinese grade is 15CrMoG (GB/T 5310) / 14Cr1MoR (GB/T 713.2).

Ready to build to spec?

Share your drawing, bill of materials or technical requirements with the Teshi team.