IBR SA106 Gr B Pipes
Teshi Group is an IBR approved stockist and supplier of IBR SA106 Gr B pipes in India — seamless pipe to ASME B36.10, NPS ½″–24″, SCH 40 to SCH 160 and XXS — for carbon steel feed water and steam lines up to about 425 °C.
Every lot is inspected by the Inspecting Authority and supplied with the IBR certificate of manufacture and test (Form III-A), EN 10204 3.1 mill certificates and full heat-number traceability.
IBR SA106 Gr B Pipes at a glance
| Supply | Stockist and supplier — Teshi Group, India |
|---|---|
| Material | ASTM A106 Gr.B · ASME SA-106 Gr.B |
| UNS | K03006 |
| EN equivalent | P235GH (EN 10216-2) |
| Chinese GB equivalent | 20 (GB/T 8163, GB/T 5310 20G) |
| Products | seamless pipe to ASME B36.10, NPS ½″–24″, SCH 40 to SCH 160 and XXS |
| Typical IBR service | Carbon steel feed water and steam lines up to about 425 °C |
| Certificate | IBR Form III-A countersigned by the Inspecting Authority; EN 10204 3.1 |
Chemical composition and strength
| Grade | C% | Cr% | Mo% | YieldMPa min | TensileMPa min | Heat treatment |
|---|---|---|---|---|---|---|
| ASTM A106 Gr.B | 0.30 max | 0.40 max | 0.15 max | 240 | 415 | Hot-finished: none required; cold-drawn: heat treat at 650 °C min |
Matching IBR components
| Component | Grade | IBR certificate |
|---|---|---|
| Pipe | ASTM A106 Gr.B | Form III-A |
| Butt-weld fittings | ASTM A234 WPB | Form III-C |
| Flanges & forged fittings | ASTM A105 | Form III-C |
How Teshi Group makes and certifies IBR material
Order review
Confirm IBR applicability, design pressure and temperature, material grade, size, rating and the Inspecting Authority named in the order.
IBR-acceptable raw material
Forging bar, billets, plate or pipe bought with mill certificates acceptable under IBR (Well-known Steel Maker or Inspecting Authority-tested material), recorded by heat number.
Manufacture
Forging, heat treatment and machining to ASME B16.5, B16.47, B16.9 or B16.11, with the heat number transferred to every piece.
Inspection and testing
Chemical and mechanical tests, hardness, dimensional inspection and NDT as required, witnessed and verified by the Inspecting Authority.
Stamping and certificate
Each piece is hard-stamped and the IBR certificate of manufacture and test is signed by Teshi Group and countersigned by the Inspecting Authority.
Dispatch
Material ships with the IBR certificate, EN 10204 3.1 mill test certificates and the dimensional report, traceable piece by piece.
IBR certificates
| Certificate (IBR 1950 name) | What it certifies | Used for |
|---|---|---|
| Form III-A | Certificate of manufacture and test of steam pipes | IBR pipes |
| Form III-B | Certificate of manufacture and test of tubes, signed by the Inspecting Authority or a Well-known Tube Maker | Boiler tubes |
| Form III-C | Certificate of manufacture and test of boiler mountings and fittings — the certificate buyers ask for with IBR flanges, fittings and valves | IBR flanges and fittings |
| Form III-F | Certificate of manufacture and test of castings, by the Inspecting Authority or a Well-known Foundry | Cast valve bodies |
| Form III-G | Certificate of manufacture and test of forgings, by the Inspecting Authority or a Well-known Forge | Forgings |
| Form IV | Steel maker's certificate of manufacture and test (Well-known Steel Maker) | Raw material |
| Form IV-A | Certificate of material tested by the Inspecting Authority where the maker's certificate is not available | Raw material |
The Indian Boiler Regulations, 2026 consolidate these certificates under a renumbered set of forms. Until your boiler inspectorate confirms the form required on a specific job, buyers and inspectors still refer to the 1950 names — Form III-A for pipes and Form III-C for flanges and fittings — and Teshi Group issues the certificate in the form prescribed at the time of supply.
FAQ
IBR SA106 Gr B Pipes: common questions
Do you supply SA106 Gr B pipes with IBR certificates?
Yes. Teshi Group supplies IBR SA106 Gr B pipes with the IBR certificate (Form III-A) countersigned by the Inspecting Authority, plus EN 10204 3.1 mill test certificates.
What is the minimum yield strength of SA106 Gr B?
240 MPa, with a minimum tensile strength of 415 MPa.
Where is SA106 Gr B used in IBR piping?
For carbon steel feed water and steam lines up to about 425 °C.
Which grades match SA106 Gr B in an IBR line?
ASTM A106 Gr.B pipe, ASTM A234 WPB butt-weld fittings and ASTM A105 flanges.
What is the Chinese equivalent of SA106 Gr B?
The nearest Chinese grade is 20 (GB/T 8163, GB/T 5310 20G).
IBR products and resources
IBR flanges
Weld neck, slip-on, socket weld and blind flanges with IBR certificates
ViewOEM manufacturerIBR butt-weld fittings
Elbows, tees, reducers and caps in WPB, WP11, WP22 and WP91
ViewOEM manufacturerIBR socket weld & threaded fittings
Forged fittings to ASME B16.11 with IBR certificates
ViewStockist & supplierIBR pipes
Seamless SA106 Gr B, P11, P22 and P91 pipe with Form III-A
ViewGuideIBR certificates — Form III-A, III-C and more
Which certificate goes with which product
ViewOverviewAll IBR products
IBR flanges, fittings and pipes from Teshi Group
View
Ready to build to spec?
Share your drawing, bill of materials or technical requirements with the Teshi team.