ISO 9001:2015IBR ApprovedEstablished 1971Full Material Traceability
GroupRequest a quote
IBRSA182 F11Form III-C

IBR SA182 F11 Flanges

Teshi Group is an IBR approved OEM manufacturer of IBR SA182 F11 flanges in India — weld neck, slip-on, socket weld, threaded, lap joint and blind flanges to ASME B16.5 (NPS ½″–24″, Class 150–2500) and B16.47 — for superheated steam to about 550 °C.

Every lot is inspected by the Inspecting Authority and supplied with the IBR certificate of manufacture and test (Form III-C), EN 10204 3.1 mill certificates and full heat-number traceability.

Request an IBR quote info@teshigroup.comIBR approved · ISO 9001:2015 · since 1971

IBR SA182 F11 Flanges at a glance

SupplyOEM manufacturer — Teshi Group, India
MaterialASTM A182 F11 Cl.2 · ASME SA-182 F11 Cl.2
UNSK11572
EN equivalent13CrMo4-5
Chinese GB equivalent15CrMoG (GB/T 5310) / 14Cr1MoR (GB/T 713.2)
Productsweld neck, slip-on, socket weld, threaded, lap joint and blind flanges to ASME B16.5 (NPS ½″–24″, Class 150–2500) and B16.47
Typical IBR serviceSuperheated steam to about 550 °C
CertificateIBR Form III-C countersigned by the Inspecting Authority; EN 10204 3.1

Chemical composition and strength

GradeC%Cr%Mo%YieldMPa minTensileMPa minHeat treatment
ASTM A182 F11 Cl.20.10–0.201.00–1.500.44–0.65275485Annealed or normalized & tempered (temper 620 °C min)

Full ASTM A182 F11 Cl.2 data sheet and PDF →

Matching IBR components

ComponentGradeIBR certificate
PipeASTM A335 P11Form III-A
Butt-weld fittingsASTM A234 WP11 Cl.1Form III-C
Flanges & forged fittingsASTM A182 F11 Cl.2Form III-C

How Teshi Group makes and certifies IBR material

Step 1

Order review

Confirm IBR applicability, design pressure and temperature, material grade, size, rating and the Inspecting Authority named in the order.

Step 2

IBR-acceptable raw material

Forging bar, billets, plate or pipe bought with mill certificates acceptable under IBR (Well-known Steel Maker or Inspecting Authority-tested material), recorded by heat number.

Step 3

Manufacture

Forging, heat treatment and machining to ASME B16.5, B16.47, B16.9 or B16.11, with the heat number transferred to every piece.

Step 4

Inspection and testing

Chemical and mechanical tests, hardness, dimensional inspection and NDT as required, witnessed and verified by the Inspecting Authority.

Step 5

Stamping and certificate

Each piece is hard-stamped and the IBR certificate of manufacture and test is signed by Teshi Group and countersigned by the Inspecting Authority.

Step 6

Dispatch

Material ships with the IBR certificate, EN 10204 3.1 mill test certificates and the dimensional report, traceable piece by piece.

IBR certificates

Certificate (IBR 1950 name)What it certifiesUsed for
Form III-ACertificate of manufacture and test of steam pipesIBR pipes
Form III-BCertificate of manufacture and test of tubes, signed by the Inspecting Authority or a Well-known Tube MakerBoiler tubes
Form III-CCertificate of manufacture and test of boiler mountings and fittings — the certificate buyers ask for with IBR flanges, fittings and valvesIBR flanges and fittings
Form III-FCertificate of manufacture and test of castings, by the Inspecting Authority or a Well-known FoundryCast valve bodies
Form III-GCertificate of manufacture and test of forgings, by the Inspecting Authority or a Well-known ForgeForgings
Form IVSteel maker's certificate of manufacture and test (Well-known Steel Maker)Raw material
Form IV-ACertificate of material tested by the Inspecting Authority where the maker's certificate is not availableRaw material

The Indian Boiler Regulations, 2026 consolidate these certificates under a renumbered set of forms. Until your boiler inspectorate confirms the form required on a specific job, buyers and inspectors still refer to the 1950 names — Form III-A for pipes and Form III-C for flanges and fittings — and Teshi Group issues the certificate in the form prescribed at the time of supply.

FAQ

IBR SA182 F11 Flanges: common questions

Do you supply SA182 F11 flanges with IBR certificates?

Yes. Teshi Group supplies IBR SA182 F11 flanges with the IBR certificate (Form III-C) countersigned by the Inspecting Authority, plus EN 10204 3.1 mill test certificates.

What is the minimum yield strength of SA182 F11?

275 MPa, with a minimum tensile strength of 485 MPa.

Where is SA182 F11 used in IBR piping?

For superheated steam to about 550 °C.

Which grades match SA182 F11 in an IBR line?

ASTM A335 P11 pipe, ASTM A234 WP11 Cl.1 butt-weld fittings and ASTM A182 F11 Cl.2 flanges.

What is the Chinese equivalent of SA182 F11?

The nearest Chinese grade is 15CrMoG (GB/T 5310) / 14Cr1MoR (GB/T 713.2).

Ready to build to spec?

Share your drawing, bill of materials or technical requirements with the Teshi team.