ISO 9001:2015IBR ApprovedEstablished 1971Full Material Traceability
GroupRequest a quote
AWWA C207FlangesTG-DS-064 · Rev. 0 · October 2026

AWWA C207 Class D Flange Dimensions

This chart gives AWWA C207 Class D steel pipe flange dimensions in inches — outside diameter, bolt circle, number and size of bolt holes, bolt size and flange thickness for ring (slip-on) and hub flanges. AWWA C207 covers steel flanges for waterworks service from 4 in to 144 in; Class D is rated 175 psi (4–12 in) / 150 psi (over 12 in).

Teshi Group manufactures AWWA C207 ring and hub flanges in India for water transmission, treatment and pumping projects.

Download PDF Request a quoteA4 · Teshi Group document TG-DS-064 · © Teshi Group · controlled document
Weld neck flange dimension drawing showing O, tf, R, X, A, Y and bolt circle WANd1KDCHFlange, raised face — section (not to scale)
Weld neck flange with raised face. Letters correspond to the column headings in the table.

Key to dimensions

D
Outside diameter of flange
C
Flange thickness, excluding raised face unless stated
N
Neck / hub diameter at base
H
Length through hub / neck length
K
Bolt circle (pitch circle) diameter
n
Number of bolts
L
Bolt hole diameter
Bolt
Bolt size (metric M or inch diameter)

AWWA C207 Class D Flange Dimensions — tables

Class D — steel ring (slip-on) flange, 175 psi (4–12 in) / 150 psi (14 in+) — inches

Class D — steel ring (slip-on) flange, 175 psi (4–12 in) / 150 psi (14 in+) — inches
SizeDFlange ODKBolt circlenBoltsLHole diaBoltSizeCSlip-on ring
497.580.750.630.625
5108.580.8750.750.625
6119.580.8750.750.688
813.511.7580.875—0.688
101614.251210.880.688
1219171210.880.812
142118.75121.1251.000.938
1623.521.25161.1251.001
182522.75161.251.131.062
2027.525201.251.131.125
2229.527.25201.3751.251.188
243229.5201.3751.251.25
2634.2531.75241.3751.251.312
2836.534281.3751.251.312
3038.7536281.3751.251.375
3241.7538.5281.6251.501.5
3443.7540.5321.6251.501.5
364642.75321.6251.501.625
3848.7545.25321.6251.501.625
4050.7547.25361.6251.501.625
425349.5361.6251.501.75
4455.2551.75401.6251.501.75
4657.2553.75401.6251.501.75
4859.556441.6251.501.875
5061.7558.25441.8751.752
526460.5441.8751.752
5466.2562.75441.8751.752.125
607369.25521.8751.752.25
668076521.8751.752.5
7286.582.5601.8751.752.625
789389642.1252.002.75
8499.7595.5642.1252.002.875
90106.5102682.4382.253
96113.25108.5682.4382.253.25
102120114.5722.6882.503.25
108126.75120.75722.6882.503.375
114133.5126.75762.9382.753.5
120140.25132.75762.9382.753.5
126147139.25803.1883.003.75
132153.75145.75803.1883.003.875
138160.5152843.4383.254
144167.25158.25843.4383.254.125

Class D — steel hub flange, 175 / 150 psi — inches

Class D — steel hub flange, 175 / 150 psi — inches
SizeDFlange ODKBolt circlenBoltsLHole diaBoltSizeCHub flangeHOverall length incl. hubNHub / neck dia
497.580.750.630.50.8755.312
5108.580.8750.750.5621.256.312
6119.580.8750.750.5621.257.562
813.511.7580.875—0.5621.259.688
101614.251210.880.6881.2512
1219171210.880.6881.2514.375
142118.75121.1251.000.751.2515.75
1623.521.25161.1251.000.751.2518
182522.75161.251.130.751.2519.875
2027.525201.251.130.751.2522
2229.527.25201.3751.2511.75—
243229.5201.3751.2511.7526.125
2634.2531.75241.3751.2511.7528.5
2836.534281.3751.2511.7530.5
3038.7536281.3751.2511.7532.5
3241.7538.5281.6251.501.1251.7534.75
3443.7540.5321.6251.501.1251.7536.75
364642.75321.6251.501.1251.7538.75
3848.7545.25321.6251.501.1251.7540.75
4050.7547.25361.6251.501.1251.7543
425349.5361.6251.501.251.7545
4455.2551.75401.6251.501.252.2547
4657.2553.75401.6251.501.252.2549
4859.556441.6251.501.3752.551
5061.7558.25441.8751.751.3752.553
526460.5441.8751.751.3752.555
5466.2562.75441.8751.751.3752.557
607369.25521.8751.751.52.7563
668076521.8751.751.52.7569
7286.582.5601.8751.751.52.7575
789389642.1252.001.75381.25
8499.7595.5642.1252.001.75387.5
90106.5102682.4382.2523.2593.75
96113.25108.5682.4382.2523.25100

Notes

  • All dimensions are in inches (1 in = 25.4 mm).
  • AWWA C207 drilling matches ASME B16.1 / B16.5 Class 125/150 drilling in the sizes they share, so AWWA flanges bolt to Class 150 valves and fittings.
  • Pressure ratings are for water service at ambient temperature; refer to the standard for test pressures.
  • Values are nominal dimensions from the standard; a dash (—) means the value is not listed. Verify against the current edition before design, purchase or fabrication.

Reference information compiled from the published standard for convenience. It does not replace the current edition of the governing standard, which takes precedence. Verify critical dimensions and properties before design, purchase or fabrication. Teshi Engineers & Sales Promoters (P) Ltd accepts no liability for errors or omissions.

Equivalent and related standards to AWWA C207 Class D Flange Dimensions

All equivalents
RegionStandardRelationship
USAAWWA C228Stainless steel waterworks flanges with C207 drilling
USAASME B16.5 Class 150 / B16.47Class 150 drilling matches C207 Class D/E up to NPS 24 — check thickness
AustraliaAS 4087Waterworks flanges

Teshi Group manufactures flanges and fittings to all of these standards on request, including Chinese GB / HG / SH and European EN dimensions for export projects. Always confirm bolting, facing and thickness when substituting one standard for another.

Dimension finder

Pick a product, standard and size — or just type — to see every dimension and download a watermarked PDF for that one size.

AWWA C207 Class D Flange Dimensions — size by size

Every size has its own page with a drawing, mm and inch values and a one-size PDF.

FAQ

AWWA C207 Class D Flange dimensions: common questions

What are the dimensions of a 24 inch AWWA C207 Class D flange?

A 24 in AWWA C207 Class D ring flange has an outside diameter of 32 in, a bolt circle of 29.5 in, 20 holes of 1.375 in and a thickness of 1.25 in.

Do AWWA C207 flanges mate with ASME Class 150 flanges?

In the sizes both standards cover the bolt circle and drilling match ASME Class 125/150, so they bolt together; thickness and pressure ratings differ.

Does Teshi Group manufacture AWWA C207 flanges?

Teshi Group manufactures steel flanges in India to AWWA C207 drilling — weld neck, slip-on, plate and blind — in carbon, alloy, stainless, duplex and nickel-alloy grades, with EN 10204 3.1 certificates.

Ready to build to spec?

Share your drawing, bill of materials or technical requirements with the Teshi team.

CallWhatsAppGet quote